Turan Borfit

WELDING TABLE

HDPE butt welding times and pressures

Heat-soak, changeover, pressure build-up and cooling times for PE 100 butt fusion by wall thickness, the times for common pipe sizes, and how to work out the gauge pressure on your machine.

The short answer

  • Set the heater plate to 220 °C ± 10 °C.
  • Form the bead at 0.15 N/mm² (1.5 kg/cm²), then heat-soak at almost zero pressure (0.01 N/mm²) for about 10 seconds per millimetre of wall.
  • Remove the plate and close the joint within the changeover time, then keep the joining pressure for the whole cooling time without moving the pipe.
  • Example: Ø 315 mm SDR 11 (28.6 mm wall) needs about 286 s of heat-soak, at most 12 s of changeover and at least 36 min of cooling under pressure.

Welding times by wall thickness

DVS 2207-1 guideline values for PE. Within each wall-thickness range, scale the value to your wall: heat-soak is 10 s per mm.

Butt welding times for PE by wall thickness (DVS 2207-1)
Wall (mm)Lip (mm)Heat (s)Remove heater (s)Fuse (s)Cool (min)
≤ 4.50.545556
4.5–7145–705–65–66–10
7–121.570–1206–86–810–16
12–192120–1908–108–1116–24
19–262.5190–26010–1211–1424–32
26–373260–37012–1614–1932–45
37–503.5370–50016–2019–2545–60
50–704500–70020–2525–3560–80

Changeover is a maximum; cooling is the minimum time under joining pressure. The pipe or fitting maker's procedure, or your project specification, takes priority over this table.

Times for common pipe sizes

Wall thickness is the pipe diameter divided by its SDR, rounded to 0.1 mm. Values are interpolated within the DVS 2207-1 ranges; check the wall thickness printed on your pipe.

Butt welding times for common PE 100 pipe sizes
Pipe Ø (mm)SDRWall (mm)Bead (mm)Heat-soak (s)Changeover max (s)Pressure build-up (s)Cooling min (min)
Ø 90SDR 118.21.5826612
Ø 90SDR 175.3153558
Ø 110SDR 11101.51007714
Ø 110SDR 176.51655610
Ø 125SDR 1111.41.51147816
Ø 125SDR 177.41.5746611
Ø 160SDR 1114.521458919
Ø 160SDR 179.41.5946713
Ø 200SDR 1118.2218291124
Ø 200SDR 1711.81.51187816
Ø 250SDR 1122.72.5227111329
Ø 250SDR 1714.721478920
Ø 315SDR 1128.63286121536
Ø 315SDR 1718.5218591124
Ø 400SDR 1136.43364151945
Ø 400SDR 1723.52.5235111330
Ø 500SDR 1145.53.5455182355
Ø 500SDR 1729.43294131637
Ø 630SDR 1157.34573212968
Ø 630SDR 1737.13.5371161946
Ø 800SDR 1172.7—————
Ø 800SDR 1747.13.5471192457
Ø 1000SDR 1190.9—————
Ø 1000SDR 1758.84588222969
Ø 1200SDR 11109.1—————
Ø 1200SDR 1770.6—————

Walls over 70 mm are beyond the DVS table: follow the pipe maker's welding procedure.

Working out the gauge pressure

The gauge shows the force spread over the machine's hydraulic cylinders, so the same weld needs a different reading on each machine. The Turan user manual gives the formula: pipe wall cross-section (cm²) × 1.5 kg/cm² for PE (1.0 for PP) ÷ total cylinder area of the machine (cm²) = bar.

The table below gives the first part, the joining force for each pipe size. Divide it by your machine's total cylinder area, from its manual or by asking us, then add the drag pressure: with the pipes clamped, raise the pressure slowly until the carriage starts to move and read the gauge.

Use the result for the bead and joining stages; heat-soak needs only enough pressure to keep contact. CNC models calculate the pressures themselves once you enter the pipe diameter and wall thickness.

Wall cross-section and joining force for PE 100 pipe
Pipe Ø (mm)SDRWall (mm)Wall section (cm²)Joining force, PE (kgf)
Ø 90SDR 118.221.132
Ø 90SDR 175.314.121
Ø 110SDR 111031.447
Ø 110SDR 176.521.132
Ø 125SDR 1111.440.761
Ø 125SDR 177.427.341
Ø 160SDR 1114.566.399
Ø 160SDR 179.444.567
Ø 200SDR 1118.2103.9156
Ø 200SDR 1711.869.8105
Ø 250SDR 1122.7162.1243
Ø 250SDR 1714.7108.7163
Ø 315SDR 1128.6257.3386
Ø 315SDR 1718.5172.3258
Ø 400SDR 1136.4415.8624
Ø 400SDR 1723.5278417
Ø 500SDR 1145.5649.7975
Ø 500SDR 1729.4434.7652
Ø 630SDR 1157.31,030.91,546
Ø 630SDR 1737.16911,037
Ø 800SDR 1747.11,114.11,671
Ø 1000SDR 1758.81,738.62,608

Gauge pressure (bar) = joining force ÷ your machine's total cylinder area (cm²) + drag pressure.

Polyethylene Pipe Butt Welding Machines

Step by step

The same sequence applies to every wall thickness; only the times and the bead height change.

  1. 1Place pieces in the clamps; insert the trimmer and face until 100% contact.
  2. 2Remove trimmer, insert heater (~220 ℃); push at 0.15 N/mm² to form the lip.
  3. 3Equalize temperature at almost zero pressure (0.01 N/mm²) with heater in place.
  4. 4Remove heater; join the pieces at 0.15 N/mm².
  5. 5Hold joining pressure for the required time, then release.
  6. 6Leave the joint to cool under the specified time.
How to choose a butt fusion machine

FAQ

Frequently asked questions

How long does an HDPE butt weld take to cool?

It depends on the wall thickness: from 6 minutes for walls up to 4.5 mm to 80 minutes at 70 mm, under full joining pressure the whole time. A Ø 315 mm SDR 11 pipe needs at least 36 minutes. Don't move, load or pressure-test the joint before the time is up.

What temperature should the heater plate be?

220 °C ± 10 °C for PE, as set out in the Turan machine manual. Check the plate temperature before every weld and keep the plate clean.

How do I work out the gauge pressure?

Multiply the pipe wall cross-section in cm² by 1.5 kg/cm² for PE, divide by the machine's total cylinder area in cm², then add the drag pressure measured on your machine. The table above gives the force for common pipe sizes. CNC models calculate it automatically.

What if the pipe wall is thicker than 70 mm?

The DVS 2207-1 table stops at 70 mm. For thicker walls, such as Ø 800 mm SDR 11, follow the pipe manufacturer's welding procedure.

Does this table override the pipe maker's instructions?

No. It gives standard DVS 2207-1 guideline values. The pipe or fitting manufacturer's procedure, or the project specification, takes priority where they differ.

Need a machine for your pipe size?

AL and ALW butt fusion machines from Ø 63 to Ø 1600 mm, with CNC models that set times and pressures automatically. Ask us for a quote.